Printer not connected to internet although internet is working

[LSD1959]

First, my Officejet 3830 stops printing saying, "There is a problem with one or more of your cartridges." They are installed properly. Meanwhile, HP Print and Scan Doctor wants to print a test page but it says not connected to internet (wireless set up). I go round and round with HO trying to get reconnected to internet. Cannot even get to the ink cartridge problem!

[Jay_G24]

Hi @LSD1959,

I'd like to help!

I understand you are receiving a cartridge error message and also unable to print from the computer.

Try the below steps to resolve the cartridge error -

Reset the printer

Reset the printer to recover from printer errors or failures.

1. If your printer has a rechargeable battery, remove it.

2. With the printer turned on, disconnect the power cord from the printer.

3. Unplug the power cord from the power source.

4. Wait 60 seconds.

5. Reconnect the power cord to a wall outlet and to the printer.

   NOTE: 

   HP recommends plugging the printer directly into a wall outlet.

6. Turn on the printer to complete the reset.

Clean the ink cartridge and carriage electrical contacts

Remove any debris or buildup from the contacts on the cartridges and in the carriage.

1. Open the door or lid to the cartridge access area. Wait until the carriage stops moving before continuing.

2. Remove the cartridge indicated in the error message from the carriage.

   • Carriages with cartridge latches: Open the latch, and then pull the cartridge up and out of the slot.

     

   • Carriages without cartridge latches: Gently press down on the cartridge to release it, and then pull it out of the slot.

     

3. Holding the cartridge by the sides, remove any protective tape that still might be on the contacts.

   CAUTION: 

   Do not touch the ink nozzles or the copper-colored electrical strip. Touching or trying to remove these parts can result in clogs, ink failure, and bad electrical connections.

   

4. Lightly dampen a lint-free cloth with distilled water, and then wipe the copper-colored contacts on the cartridge.

   

5. Lightly dampen a lint-free cloth or swab with distilled water, and then clean the electrical contacts in the carriage.

   

6. Wait 10 minutes for the contacts to dry, and then reinsert the cartridge into its color-coded slot.

7. Repeat these steps for the other cartridge if it was indicated in the error message.

8. Close the door or lid to the cartridge access area.

   If the error persists, clean the cartridge and carriage contacts a second time.

Also, help me with the below details -

What is the status of the wireless light on the printer, steady or blinking?

Is the printer connected to a home or public network?

I would like to know, is your router set to work on 2.4 GHz network or 5 GHz network band?

Hope this helps! Keep me posted. 

And, Welcome to the HP Support Community. 

Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.

Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping

[LSD1959]

Wifi not blinking. Cartridges are clean. Tried reset. 😢

[Jay_G24]

 Try the below suggestions to resolve the printer offline issue-

 Use HP Print and Scan Doctor to check connectivity

Download a special version of HP Print and Scan Doctor specifically created to help with printer offline conditions.

1. Download HP Print and Scan Doctor.
2. Run HPPSdr.exe from the download location on your computer.
3. Once HP Print and Scan Doctor opens, click Start, and then select your printer.
   • If your printer in not in the list, turn it off and on, and then click Retry.
   • If there is a connection problem, follow the instructions in HP Print and Scan Doctor.
4. If a screen prompts you to turn on printer updates, click Yes.
5. If a screen prompts you to make your printer the default printer, click Yes.

Set a manual IP-

To set a manual IP and try the steps below -

--->Touch on the wifi icon ((i)) on the printer, and take down the IP address 

--->Open a web browser (ex Chrome or Mozilla) and type in the printer's IP

--->then go to network ---> general ---> network protocols ---> select IPV4 only-->apply 

--->go to wireless ---> wireless 802.11---> select manual ip ---> apply

--->Enter 8.8.8.8 for the first DNS and 8.8.4.4 for the second DNS.  

--->then go to settings on the main ews page --> power management ---> select sleep mode to max 15min

 Connect the printer to TCP/IP port

 --->Touch on the wifi icon ((i)) on the printer, and take down the IP address 

a. Click Start/Devices and Printers.  Right-click on your HP Printer.  Select Printer Properties.  Select the Ports tab at the top.

b.    Select Add Port.  Select Standard TCP/IP Port.  Select New Port.

c.    Follow the Add Port Wizard.  Under Printer Name or IP Address, .  Example:  192.168.1.15.  The IP address will be copied under Port Name.  

d.    Select Next and Finish the Wizard.

Hope this helps! Keep me posted.