ERROR CODE OXOO829C98 HW WatchDog

[Melissa2924]

I changed the black ink cartridge and added paper to the printer. I then had a paper jam that I had to clear. Once I cleared that, I tried to restart and I have received this error ever since. I have followed the steps in doing a Hard Reset and that did not work. 

I am unable to install updates because my printer is now offline and wont connect to my HP Smart App.

I cannot install any updates directly onto my printer because it wont move from the ERROR CODE Screen. I have followed all the links previously provided in other Messages regarding this error code and nothing is working. 

How do I get to a different screen on my printer to be able to fix this?

[KrazyToad]

hi

[KrazyToad]

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.

@Melissa2924

Welcome to HP Support Community

I would like to help

Please try these steps

- Turn on the printer.

- Wait until the printer is idle and silent before you continue.

- Disconnect the USB cable from the rear of the printer. If your printer has a network or wireless connection, leave it connected.

- Remove the ink cartridges from the printer.

- With the printer turned on, disconnect the power cord from the rear of the printer and from the wall outlet or power strip.

- Wait at least 60 seconds.

- Plug the power cord back into the wall outlet.

NOTE: HP recommends connecting the printer power cord directly to a wall outlet.

- Reconnect the power cord to the rear of the printer.

- Turn on the printer, if it does not automatically turn on.

- The printer might go through a warm-up period. The printer lights might flash, and the carriage might move.

- Wait until the warm-up period finishes and your printer is idle and silent before you proceed.

- Reinsert the ink cartridges, and then close the ink cartridge access door.

- If you receive a prompt to print a calibration page, do so.

Ensure the Firmware is updated https://support.hp.com/in-en/document/c02919168

Thank you

If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" on this Post and it will also help other community members with similar issue.