• ×
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
  • ×
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
Guidelines
The Poly Phones Knowledge Base is live! We look forward to helping you with common issues and troubleshooting advice!
Locked

‎11-15-2012 05:10 AM

HP Recommended

Hi

 

I'm trying to get a test IP450 to switch to the Lync base profile via config file, rather than having to later explain to people to simultaneously press 1,2,4,5 and switch manually as per the admin manual. Could someone help with the config file directive needed to get the phone to switch to the Lync profile on first boot?

 

Thanks,

1 ACCEPTED SOLUTION

Accepted Solutions

‎11-15-2012 05:20 AM

HP Recommended

Hello thefish,

 

as usual I can only recommend to always check the admin guide:

 

Page 416 UCS 4.1.0

 

device.baseProfile

 

You will need to add device.set="1" as well as with all device parameters.

 

device.set="1" device.baseProfile.set="1" device.baseProfile="lync"

 

 

Best Regards

 

Steffen Baier

------------------------------------------------
Notice: I am an HP Poly employee but all replies within the community are done as a volunteer outside of my day role. This community forum is not an official HP Poly support resource, thus responses from HP Poly employees, partners, and customers alike are best-effort in attempts to share learned knowledge.
If you need immediate and/or official assistance for former Poly\Plantronics\Polycom please open a service ticket through your support channels
For HP products please check HP Support.

Please also ensure you always check the General VoIP , Video Endpoint , UC Platform (Microsoft) , PSTN

View solution in original post

Was this reply helpful? Yes No
2 REPLIES 2

‎11-15-2012 05:20 AM

HP Recommended

Hello thefish,

 

as usual I can only recommend to always check the admin guide:

 

Page 416 UCS 4.1.0

 

device.baseProfile

 

You will need to add device.set="1" as well as with all device parameters.

 

device.set="1" device.baseProfile.set="1" device.baseProfile="lync"

 

 

Best Regards

 

Steffen Baier

------------------------------------------------
Notice: I am an HP Poly employee but all replies within the community are done as a volunteer outside of my day role. This community forum is not an official HP Poly support resource, thus responses from HP Poly employees, partners, and customers alike are best-effort in attempts to share learned knowledge.
If you need immediate and/or official assistance for former Poly\Plantronics\Polycom please open a service ticket through your support channels
For HP products please check HP Support.

Please also ensure you always check the General VoIP , Video Endpoint , UC Platform (Microsoft) , PSTN
Was this reply helpful? Yes No

‎11-15-2012 06:15 AM

HP Recommended

Thank you, I was looking on page 261 which says to refer to the provisioning guide, which doesnt seem to have this.

 

Cheers,

Was this reply helpful? Yes No
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the Terms of Use and Rules of Participation.
Didn't find what you were looking for? Ask the community
† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the <a href="https://www8.hp.com/us/en/terms-of-use.html" class="udrlinesmall">Terms of Use</a> and <a href="/t5/custom/page/page-id/hp.rulespage" class="udrlinesmall"> Rules of Participation</a>.