hp 415 print head error

[WENG0917]

i install a new tri color cartridge on 415 printer but after 3 weeks the print head error is back again. red blinking light  on tri color.now i cant my printer,what should i do now ?please help me solve this issue!

[sandytechy20]

@WENG0917 

Welcome to the HP Support Community. I'd be happy to assist you with the  "Problem with printhead"

Let's try a power reset on the printer

Reset the product

• With the printer turned on, disconnect the power cord from the rear of the printer.
• Unplug the power cord from the wall outlet.
• Wait at least 60 seconds.
• Plug the power cord back into the wall outlet.
• Reconnect the power cord to the printer.
• Turn the printer on. HP recommends plugging the printer directly into a wall outlet.

 Try the steps in the below -

Step 1: Determine which printhead caused the error

Look at the printer display or control panel to determine which printhead caused the error.

If the Cartridge Problem error has a Tri-color icon or the blinking icon is above the Tri-color icon, the Tri-color cartridge caused the error.

If theCartridge Problem error has a Black icon or the blinking icon is above the Black icon, the Black cartridge caused the error.

If the Cartridge Problem error has both Tri-color and Black icons or the blinking icons are above both Tri-color and Black icons, both cartridges caused the error.

Step 2: Remove, inspect, and then reseat the printheads

The printer might display an error if the printheads are not correctly installed. Perform the following steps only for the printhead indicated on the printer control panel.

Turn on the printer.

Make sure plain paper is loaded in the input tray.

Make sure all ink tanks are at least half full.

Open the front door, and then open the printhead access door.

Wait until the carriage stops moving before you continue.

Make sure the printhead carriage latch is closed.

If the printhead latch is closed, continue with these steps.

If the printhead latch is open, push down on the latch to close it, close the front door, and then try to print. If the error persists, continue with these steps.

Push down on the carriage latch to unlock it.

Press down on the printhead to release it, pull it out of its slot, and then set it aside on a protected surface, such as a sheet of paper.

   CAUTION: 

To prevent ink from leaking or transferring, hold the printhead by the sides and keep the printhead upright at all times.

Make sure the plugs on top of the printhead have been removed.

Make sure the tape from the printhead contacts has been removed.

   CAUTION: 

Do not touch the copper-colored contacts or the ink nozzles. Do not replace the protective tape on the contacts. Handling these parts can result in clogs, ink failure, and bad electrical connections.

Slide the printhead at a slight upward angle into its slot, and then push up on the printhead until it snaps into place.

Repeat the previous steps for the other printhead, only if indicated by the Printhead icon or error message.

Close the carriage latch by pushing it down until it locks into place.

Close the front door

Align the printheads.

If your printer has a touchscreen control panel, follow the control panel prompts to print an Alignment Page, and then follow the instructions on the page to align the printheads.

If your printer does not have a touchscreen control panel, an A blinks on the control panel and an Alignment Page prints automatically. Follow the instructions on the page to align the printheads.

If the error persists, continue to the next step.

Step 3: Reset the printer

Resetting the printer can sometimes resolve this error.

With the printer turned on, disconnect the power cord from the printer.

Unplug the power cord from the power source.

Wait 60 seconds.

Reconnect the power cord to a wall outlet and to the printer.

NOTE: 

HP recommends plugging the printer directly into a wall outlet.

Keep me posted.

If this helps, please mark the public post as an accepted solution so that it benefits several others

Cheers.