• ×
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
  • ×
    Information
    Need Windows 11 help?
    Check documents on compatibility, FAQs, upgrade information and available fixes.
    Windows 11 Support Center.
  • post a message
Guidelines
The Poly Phones Knowledge Base is live! We look forward to helping you with common issues and troubleshooting advice!
HP Recommended

We use IP Station Duo (SIP), registered to Cisco Call Manger, it got issue with external DTMF IVR.

I found detail from this knowledgebase

 

http://community.polycom.com/t5/VoIP/FAQ-Phone-unable-to-send-DTMF-to-an-IVR-system-or-how-to/td-p/4...

 

 

I have been up load the "dtmf_payload_127.cfg" still did not working, or which configuration path that I can do revise ?

config_files.cfg, web.cfg,devices_settings.cfg or phone_local.cfg ?    

 

Cisco engineer checked on voice gateway and ask to change DTMF tone to be 127:

 <dtmf>
  <tone tone.dtmf.rfc2833Payload="127"/>
 </dtmf>

 

Phone Information Phone Model SoundStation Duo Part Number 3111-19000-001 Rev:H         UC Software Version 4.0.12.0926 BootROM Software Version 5.0.12.0033

1 ACCEPTED SOLUTION

Accepted Solutions
HP Recommended

Yup, I tried to put under "web" and under "config_file" after restored and rebooted, that command was gone from configution file when backup to verifyed so it dtfm still not working..  how can I pass you my configuration fil ?  if you can edit for me.

thanks

 

View solution in original post

4 REPLIES 4
HP Recommended

Hello IT_easycompare,

welcome to the Polycom Community.

The community's VoIP FAQ contains this post here:

 

May 25, 2017 Question: Can I create a backup of my current configuration?

Resolution:Since UC Software 4.0.0 or later a backup can be created via the Web Interface Utilities > Phone Backup & Restore > Phone Backup > Phone Backup


Utilizing the above simple instructions enables you to check within your backup <Web section if the added configuration is present.

 

As you are using a software later than 3.2.0 the payload type requested by the Cisco Engineer is already used.

 

I suggest to use the rest of the FAQ post to troubleshoot this.


Please ensure to provide some feedback if this reply has helped you so other users can profit from your experience.

Best Regards

Steffen Baier

Polycom Global Services

------------------------------------------------
Notice: I am an HP Poly employee but all replies within the community are done as a volunteer outside of my day role. This community forum is not an official HP Poly support resource, thus responses from HP Poly employees, partners, and customers alike are best-effort in attempts to share learned knowledge.
If you need immediate and/or official assistance for former Poly\Plantronics\Polycom please open a service ticket through your support channels
For HP products please check HP Support.

Please also ensure you always check the General VoIP , Video Endpoint , UC Platform (Microsoft) , PSTN
HP Recommended

Yup, I tried to put under "web" and under "config_file" after restored and rebooted, that command was gone from configution file when backup to verifyed so it dtfm still not working..  how can I pass you my configuration fil ?  if you can edit for me.

thanks

 

HP Recommended

Hello IT_easycompare,

As already outlined the Payload is 127 as a standard and therefore if set agin is removed as we are already applying this value.

 

The backup of the configuration will only show parameters that differ from the standard.

Please ensure to provide some feedback if this reply has helped you so other users can profit from your experience.

Best Regards

Steffen Baier

Polycom Global Services

------------------------------------------------
Notice: I am an HP Poly employee but all replies within the community are done as a volunteer outside of my day role. This community forum is not an official HP Poly support resource, thus responses from HP Poly employees, partners, and customers alike are best-effort in attempts to share learned knowledge.
If you need immediate and/or official assistance for former Poly\Plantronics\Polycom please open a service ticket through your support channels
For HP products please check HP Support.

Please also ensure you always check the General VoIP , Video Endpoint , UC Platform (Microsoft) , PSTN
HP Recommended

Ok,

 

1. exported  web file and put the revised payload to 101, 

web>

  tone.dtmf.onTime="100"
  tone.dtmf.rfc2833Payload="101"

 />

 

2. inport again.

 

 

 Then it worked right now, Thanks. 

 

† The opinions expressed above are the personal opinions of the authors, not of HP. By using this site, you accept the <a href="https://www8.hp.com/us/en/terms-of-use.html" class="udrlinesmall">Terms of Use</a> and <a href="/t5/custom/page/page-id/hp.rulespage" class="udrlinesmall"> Rules of Participation</a>.