-
×InformationNeed Windows 11 help?Check documents on compatibility, FAQs, upgrade information and available fixes.
Windows 11 Support Center. -
-
×InformationNeed Windows 11 help?Check documents on compatibility, FAQs, upgrade information and available fixes.
Windows 11 Support Center. -
- HP Community
- Printers
- Printer Wireless, Networking & Internet
- HP ENVY 6000 SERIES shows ERROR and won't print

Create an account on the HP Community to personalize your profile and ask a question
10-08-2022 08:33 PM
This HP ENVY 6000 All-in-One Printer series printer has been working just fine when I was connected via a HOTSPOT. I have not moved. The printer has not moved. I did start using a BROADBAND for internet connections. Now...... I keep getting ERROR when I try to print anything from anywhere. I can't print from my laptop and can't print from any website. I do have internet connection on the laptop. It also keeps showing OFFLINE. I have been trying everything from UNinstalling printer and then installing again. The printer shows that it is ON. I just can't get it to understand that it is not on the HOTSPOT any longer and that it must connect to the BROADBAND. HOW do I do this......PLEASE!! I have been trying anything and everything for the last 3 days. I just need to know how to make the printer pick up the new internet access. Thanks in advance.
10-11-2022 05:49 AM - edited 10-11-2022 05:49 AM
Hi @Ginakins77,
Welcome to the HP Support Community
I understand you are facing a connectivity issue with your HP ENVY 6000 Printer. Not to worry I will help you to get a resolution to resolve the issue.
To assist you better:
- Is the blue Wi-Fi light solid on the printer? ( if the Wi-Fi Light is blinking then please re-connect the printer back to your Wi-Fi router - Restore Wi-Fi setup mode on your HP printer, Once you restore the network to defaults, then please follow the instructions on this link to connect the printer back to your PC.)
- How far is the printer located from the WiFi router?
- Do you have a dual-band router?
- If you have a Dual-band router and both 2.4GHz and 5GHz networks share the same name/SSID, the printer will not be able to connect to the network. In this case, contact your Internet service provider to assign different names to both networks.
While you respond to that, Let's perform a power drain:
- With the printer turned on, disconnect the power cord from the rear of the printer and also unplug the power cord from the wall outlet.
- Remove USB cable, if present.
- Wait for 2-3 minutes, press and hold the power button on your printer for about 30 seconds to remove any additional charge.
- Now plug back the power cable straight to a wall outlet without any surge protector or an extension cord (This is important) and then plug back the power cord to the printer.
- Turn on the printer and wait till warm-up period finishes and the printer is idle
Update the printer firmware
- Click here to download and install the latest printer firmware from your product
- Click here to know different methods of updating printer firmware.
If the issue persists, then please follow the below steps to resolve the issue.
Use HP Print and Scan Doctor to check connectivity
Download a special version of HP Print and Scan Doctor specifically created to help with printer offline conditions.
- Download HP Print and Scan Doctor.
- Run HPPSdr.exe from the download location on your computer.
- Once HP Print and Scan Doctor opens, click Start, and then select your printer.
- If your printer in not in the list, turn it off and on, and then click Retry.
- If there is a connection problem, follow the instructions in HP Print and Scan Doctor.
- If a screen prompts you to turn on printer updates, click Yes.
- If a screen prompts you to make your printer the default printer, click Yes.
Set a manual IP-
To set a manual IP and try the steps below -
--->Touch on the wifi icon ((i)) on the printer, and take down the IP address
--->Open a web browser (ex Chrome or Mozilla) and type in the printer's IP
--->then go to network ---> general ---> network protocols ---> select IPV4 only-->apply
--->go to wireless ---> wireless 802.11---> select manual ip ---> apply
--->Enter 8.8.8.8 for the first DNS and 8.8.4.4 for the second DNS.
--->then go to settings on the main ews page --> power management ---> select sleep mode to max 15min
Connect the printer to TCP/IP port
--->Touch on the wifi icon ((i)) on the printer, and take down the IP address
a. Click Start/Devices and Printers. Right-click on your HP Printer. Select Printer Properties. Select the Ports tab at the top.
b. Select Add Port. Select Standard TCP/IP Port. Select New Port.
c. Follow the Add Port Wizard. Under Printer Name or IP Address. Example: 192.168.1.15. The IP address will be copied under Port Name.
d. Select Next and Finish the Wizard.
Hope this helps! Keep me posted.
Please click “Accepted Solution” if you feel my post solved your issue, it will help others find the solution. Click the “Kudos/Thumbs Up" on the bottom right to say “Thanks” for helping!
ANAND_ANDY
I am an HP Employee