Hp 589 printer stops printing halfway and show e3 error

[Vishal114]

Hp 589 printer stops printing halfway and show e3 error. I did every possible method from cleaning to cartridge change but nothing happens. After 5 6 pages printing it shows e3 and  ! Starts blinking on screen. 

[Raj_05]

Hi @Vishal114,

Welcome to HP Support Community.

Thank you for posting your query, I will be glad to help you.

It sounds like you're dealing with an E3 error on your HP Smart Tank 589 printer, and it's frustrating that the usual troubleshooting steps haven't resolved the issue. The E3 error on HP printers typically indicates a paper jam or a sensor issue. Since you've already checked for paper jams and replaced the cartridges, there are a few more things we can try.

Reset the Printer: Sometimes a simple reset can clear up internal issues.

• Turn off the printer.
• Unplug the power cord from the printer and the wall outlet.
• Wait a few minutes (at least 30 seconds) to allow the printer to reset.
• Plug the power cord back into the wall outlet and then into the printer.
• Turn on the printer and see if the error persists.

Check Paper Path and Sensors: Even if you don't see a jam, there might be a small piece of paper stuck somewhere not easily visible. Follow these steps:

• Remove all paper from the input tray and the output tray.
• Open the printer cover and check for any jammed paper inside.
• Use a flashlight to inspect the paper path thoroughly.
• Check if there's any debris or foreign objects obstructing the sensors.

Clean Paper Feed Rollers: Dirty or worn-out rollers can cause paper feeding problems.

• Open the printer cover.
• Locate the paper feed rollers (they are rubber rollers behind the paper tray).
• Use a lint-free cloth lightly moistened with water to clean the rollers.
• Make sure they are dry before closing the cover and trying to print again.

Update Printer Firmware: Sometimes firmware updates can resolve known issues.

• Go to the HP Support website and search for your printer model.
• Download and install the latest firmware available for your printer.
• Follow the instructions provided to update the firmware.

I hope this helps.

Take care and have a good day.

Please click “Accepted Solution” if you feel my post solved your issue, it will help others find the solution. Click the “Kudos/Thumbs Up" on the bottom right to say “Thanks” for helping!

Alden4

HP Support 

[Vishal114]

I tried cleaning also but not solved the problem. When I was doing printing, the feed roller sounds like jams. After 2 to 3 prints, feed roller doesn't taking paper or it stops on half of the paper, and suddenly it shows E3 ERROR and   ! Starts blinking in screen

[Raj_05]

Hi @Vishal114,

Thank you for your response, 

It sounds like you're experiencing some technical issues with your HP 589 printer. The error code E3 usually indicates a paper jam or a problem with the paper feed mechanism. Here are some steps you can try to resolve the issue.

• Check for Jammed Paper: Turn off the printer and carefully check for any jammed paper inside the printer. Make sure to remove any bits of torn paper that you find.
• Check Paper Quality and Size: Ensure that you're using the correct size and type of paper recommended for your printer. Sometimes, using wrinkled, curled, or damp paper can cause feeding issues.
• Adjust Paper Guides: Make sure that the paper guides in the paper tray are properly aligned with the edges of the paper. Misaligned paper guides can cause the paper to feed incorrectly.
• Inspect Paper Path: Carefully examine the paper path for any obstructions or foreign objects that may be blocking the paper feed mechanism.

By following these steps, you should be able to troubleshoot and resolve the E3 error and paper feeding issues with your HP 589 printer. Let me know if you need further assistance!

I hope this helps.

Take care and have a good day.

Please click “Accepted Solution” if you feel my post solved your issue, it will help others find the solution. Click the “Kudos/Thumbs Up" on the bottom right to say “Thanks” for helping!

Alden4

HP Support